Feather RP2040 24-pin E-Paper - board with RP2040 microcontroller and display connector - Adafruit 5727
- Артикул:
- 91724213
Характеристики
- UC - I2C
- yes
- UC - A/C
- 12-bit
- UC - USB
- USB C
- UC - UART
- yes
- UC - Вспышка
- 8 MB
- Интерфейс UC - SPI
- yes
- UC - Микроконтроллер
- RP2040
Общие характеристики
- UC - PWM
- 16
Прочие свойства
- Бренд
- Adafruit
Описание
Adafruit Feather RP2040 with a 24-pin connector for connecting E-Paper displays is a board based on the RP2040 microcontroller, with a dual-core ARM Cortex M0+ with a clock speed of up to 133 MHz, equipped with 264 kB of RAM and 8 MB of Flash memory operating via the QSPI interface. The microcontroller is equipped with such interfaces as: 2 x I2C , 2 x SPI , 2 x UART, 16 PWM channels and 4 x ADC . The 24-pin connector on the board allows you to connect any E-Paper display that uses this interface. There is also a STEMMA QT connector at the user's disposal for easy connection of modules using the I2C interface without the need for soldering.
The RP2040-based platform supports many programming languages, such as MicroPython , CircuitPython and C/C++ . The program can be implemented using the USB interface (USB type C connector), using the built-in UF2 bootloader, or through an external programmer. In addition, the board has a red LED and a Neopixel RGB LED.
Feather RP2040 24-pin E-Paper - board with RP2040 microcontroller and display connector - Adafruit.
The board has a JST connector, which can be used to connect the battery to it.
The JST connector is used to connect a lithium-ion (Li-Ion) or lithium polymer (LiPol) battery to power the board. After connecting the power supply via the USB connector, the built-in charging system allows you to charge the battery with a maximum current of 200 mA. The charging status is indicated by a dedicated LED. The system detects the connection of the power supply, thanks to which it is possible to use the battery as a UPS.
Do not connect batteries other than those indicated by the manufacturer - Li-Ion, Li-Pol - with a maximum voltage of 4.2 V to the JST port. This may damage the charging system.
- Two ARM Cortex M0+ cores clocked up to 133 MHz
- 264KB of RAM
- No built-in memory - support external FLASH QSPI memory up to 16 MB
- DMA controller
- Built-in LDO for core power
- 30 GPIO pins
- Interfaces:
- 2 x UARTs
- 2 x SPI
- 2 x I2C
- 16 PWM channels
- 4 x 12-bit ADCs
- USB 1.1 controller and PHY
- 8 PIO state machines
Feather RP2040 24-pin E-Paper.
Pin placement.
- USB type C connector - used for power and data transfer. It allows you to program the microcontroller through the built-in UF2 Bootloader.
- JST connector - 2-pin connector used to connect the Li-Ion or Li-Pol battery to power the board, at the same time used to charge the battery.
- GND - system ground
- BAT - positive voltage common to JST socket for optional battery
- USB - positive voltage common with the USB C socket
- EN - pin enabling the built-in 3.3 V regulator, to turn it off, connect it to ground
- 3.3 V - outputs of the voltage stabilizer
- RP2040 microcontroller
- 32-bit dual-core Cortex M0+
- 264KB of RAM
- 8 MB external QSPI FLASH memory
- 24-pin E-Paper display connector
- GPIO connectors:
- 2x I2C, 2x SPI, 2x UART
- 16 PWM channels
- 4 x 12-bit ADCs
- 8 digital leads
- Built-in LED and Neopixel RGB
- STEMMA QT connector
- SWD interface
- Reset and Bootloader buttons
- 3.3V voltage stabilizer
- Battery power connector
- USB type C connector - for charging the battery and programming
- Language support: MicroPython, CircuitPython and C/C++
- 4 mounting holes
- Dimensions: 50.8 x 22.8 x 7.0mm
- Weight 6.3g
- Feather RP2040 - Adafruit 5727
- 2 x goldpin plug 2x16 raster 2.54 mm
Components included in the set.
- Manufacturer's website
- User Guide
- RP2040 microcontroller documentation
- Description of board pins
- CircuitPython Basics
- Configuration in the Arduino IDE
- Circuit diagrams
Доставка
Мы доставляем товары напрямую из Германии в Россию курьерской службой или в почтовое отделение. Вы можете выбрать подходящий для вас способ доставки при оформлении заказа. Стоимость доставки зависит от выбранного метода и начинается от 711 руб. Время доставки зависит от выбранного города и метода доставки, но в среднем занимает от 10 до 30 дней. Если вы оформите заказ прямо сейчас, мы доставим его в период с 16 июля - 5 августа.
На протяжении уже более 10 лет мы работаем с надежными и проверенными нами службами и предлагаем доставку электрики Adafruit в различные города России, такие как Москва, Санкт-Петербург, Новосибирск, Екатеринбург, Казань, Нижний Новгород, Челябинск, Самара, Уфа, Ростов, Омск, Красноярск, Воронеж и другие.
Вы всегда можете отследить свой заказ, используя номер посылки, сразу как только он будет отправлен к вам с нашего склада.
Мы сотрудничаем с поставщиками электрики Adafruit и предлагаем вам самые выгодные предложения на брендовые товары из Америки. Опираясь на свой многолетний опыт, выбираем только лучшие позиции из аутлетов и дискаунтеров, чтобы предоставить вам оптимальные цены, в которые не включены дополнительные расходы на аренду торговых помещений.
Доставка товаров осуществляется прямо с нашего склада до указанного вами адреса. Вы получаете оригинальный товар по цене, которая недоступна для местных магазинов. В нашем интернет-магазине вы всегда найдете широкий ассортимент брендовых товаров с выгодными скидками.
Мы следим за каждым этапом вашей покупки и предоставляем отслеживание заказа на всех этапах, начиная с момента оплаты.